Kingfisher Fishfull Thinking 56 day Build

This topic is empty.

Viewing 25 posts - 1 through 25 (of 101 total)

1 2 3 4 5 →

Author

Posts
9 August 2013 at 22:31 #42784
Nigel Edwards
Participant
@nigeledwards16506
This is what i have hand crafted from plans 1958 kingfisher, I will add the full build hope you all enjoy

Edited By nigel edwards 1 on 09/08/2013 22:33:06

Edited By nigel edwards 1 on 09/08/2013 22:36:14
Advert

9 August 2013 at 22:31 #6891
Nigel Edwards
Participant
@nigeledwards16506
New to the world of boat building this is my first build
9 August 2013 at 22:39 #42785
Nigel Edwards
Participant
@nigeledwards16506
It all started with a couple of days clearing the shed of junk building the work bench and shelving with the help of one of the younger boys, had to refelt the roof which I could of done with out as it broke into the build budget but we have to be water tight..
9 August 2013 at 22:42 #42786
Nigel Edwards
Participant
@nigeledwards16506
Day 3 started with a raid of my mothers loft, found some 9mm ply from my late fathers projects which I shall use for the keel and frame assembly, also found some mdf slats from a kitchen blind 25mm wide 2mm thick bends and twist nicely so shall give this a go for planking the hull..
9 August 2013 at 22:45 #42787
Nigel Edwards
Participant
@nigeledwards16506
Printed out the plans 16 pages of A4 paper per plan done this 3 times 1 set for master others sets for templates, wife was not very happy as I run the ink out in the printer oopps..

Edited By nigel edwards 1 on 09/08/2013 23:04:36
9 August 2013 at 22:49 #42788
Nigel Edwards
Participant
@nigeledwards16506
After spending a couple of hours tangled up in paper cuttings and sticky tape I managed to fit all frame templates on one sheet of recycled ply stuck down with the kids glue stick robed from the stationary draw, "I will replace it honest"

Edited By nigel edwards 1 on 09/08/2013 22:53:14

Edited By nigel edwards 1 on 09/08/2013 22:53:40

Edited By nigel edwards 1 on 09/08/2013 23:05:46
9 August 2013 at 22:51 #42789
Nigel Edwards
Participant
@nigeledwards16506
Day4 After waiting for my new jigsaw to arrive as the old one was rubbish, I rough cut out all the pieces will cut out the notches for the keel and deck beams after sanding and shaping.

Edited By nigel edwards 1 on 09/08/2013 22:54:07

Edited By nigel edwards 1 on 09/08/2013 23:02:44
9 August 2013 at 22:57 #42790
Nigel Edwards
Participant
@nigeledwards16506
Day 8 after a couple of days break I took some advice and made a new jig today made my own stone circle "block henge" hope this works

Edited By nigel edwards 1 on 09/08/2013 23:03:35
9 August 2013 at 22:59 #42791
Nigel Edwards
Participant
@nigeledwards16506
dry fit of frames on jig, don't breathe as it will go down like a domino's and yes that did happen about 5 times

Edited By nigel edwards 1 on 09/08/2013 23:06:56
9 August 2013 at 23:09 #42792
Nigel Edwards
Participant
@nigeledwards16506
Day 9 Had a lazy day today, all that,s been done is I shaved and sanded the angles on the frame pieces so planking fits flush. need to wait for some parts to turn up prop shaft mainly so i can line up and drill the keel before glueing frame sections
9 August 2013 at 23:11 #42793
Nigel Edwards
Participant
@nigeledwards16506
Day 12 Well my parts never arrived today so not to waste a day I made the mast, hand plain and sand paper done the trick..

Edited By nigel edwards 1 on 09/08/2013 23:12:12
9 August 2013 at 23:13 #42794
Nigel Edwards
Participant
@nigeledwards16506
Day 13 Let The build continue
9 August 2013 at 23:23 #42795
Nigel Edwards
Participant
@nigeledwards16506
Well bit of progress today after parts arrived and test fitted shaft motor alignment all worked out nice dropped into place between frames nicely.. frames are all glued to keel now, also shaped and fitted the transom..
9 August 2013 at 23:24 #42796
Nigel Edwards
Participant
@nigeledwards16506
Day 14 The planking has started drawing pins to hold while glueing..
9 August 2013 at 23:26 #42797
Nigel Edwards
Participant
@nigeledwards16506
Day 15 Slow progress today with the Pin Soldiers, what a task this is..
9 August 2013 at 23:27 #42798
Nigel Edwards
Participant
@nigeledwards16506
Day 16 Well the hull planking is done, that was the worst job by far, and when I removed it from the jig the rear frame was out of line grrrr apart from that it seems to be all in shape.. will give it a full day to dry off now before removing all them pins..

Edited By nigel edwards 1 on 09/08/2013 23:29:07
9 August 2013 at 23:30 #42799
Nigel Edwards
Participant
@nigeledwards16506
Day 17 Ok all them pesky pins was removed today it held up great, have pre sanded it ready for filler, shape don't look too bad I am pleased with the result so far
9 August 2013 at 23:34 #42800
Nigel Edwards
Participant
@nigeledwards16506
Day 18/19 update so far the last couple of days I fitted the base for the motor mount lined up great, also dry fitted the rudder had to make a block for the rudder to sit flush and straight for a good seal, as you can see in the pictures quite pleased with the result bit of carving with a wood rasp..
9 August 2013 at 23:36 #42801
Nigel Edwards
Participant
@nigeledwards16506
Day 19 continued under deck cut out trimmed shaped and dry fitted using 3.6mm ply been a busy afternoon..
9 August 2013 at 23:38 #42802
Nigel Edwards
Participant
@nigeledwards16506
Day 20/21 update filled and sanded the hull..
9 August 2013 at 23:42 #42803
Nigel Edwards
Participant
@nigeledwards16506
Day 22 Been too hot to work for my liking in the 30's easy, rare weather for us brits, so took it easy and just made the servo mount. and made the most of the weather..
9 August 2013 at 23:44 #42804
Nigel Edwards
Participant
@nigeledwards16506
Day 24 Waiting for the deck planking to arrive have ordered Walnut Strips 1.5mm x 10mm in the mean time I made the side rails once deck is planked shall fit these..
9 August 2013 at 23:46 #42805
Nigel Edwards
Participant
@nigeledwards16506
Day 25 parts arrival.. Mfa Titan High power 12v 3Ah Lead Acid Bat, 12v 7h charge plug charger, Viper Marine 15 speed control all from**LINK**

10ml Waterproof Marine Grease from Nautical Marine Models (ebay)
9 August 2013 at 23:48 #42806
Nigel Edwards
Participant
@nigeledwards16506
Day 25 continued Made a battery mount for the titan piece of ply 2 screws and screw cups and a piece of rubber glazing seal from a green house to secure it, bat fits perfect in between frames with about 1mm clearance was lucky there.. will glue in to place at a later date as it can go in 1 or two places within the hull depending on ballast and how she sits in the water..
9 August 2013 at 23:50 #42807
Nigel Edwards
Participant
@nigeledwards16506
Day 26 Today so far have cut the side rails supports bit longer than they need to be from 6 x 6mm square pine will be glued in place when under deck planked.. finding any job to do now wile waiting for this walnut to turn up grrrrrr
Author

Posts